I wouldn’t describe building a PC as "easy"; but it’s not as difficult as one might imagine. Unlike constructing an electronic circuit, such as an amplifier, for example; there’s nothing extremely fiddly, such as soldering or quality engineering to worry about: That’s all been taken care of already by the component manufacturers.

It’s like putting a jigsaw together: Every piece fits in a certain configuration as a part of the whole. The pieces are already made, so you don’t have to make them yourself: you only need to fit them together in the correct fashion.

*At this point I’ll state that this article isn’t a comprehensive how-to: It’s just some notes from my recent rebuild experience.*

You may have heard that I recently had a computer die on me. I’d built it from scrap parts as a replacement for another one that went funny earlier. I have no idea exactly what caused the fault that killed it. It blue-screened and then just died a second later. Following on from that when I tried to restart it the BIOS couldn’t find the processor; so I assumed that the chipset had fried: ‘New motherboard required if this was the case.

There’s the old construction on the left. (Excuse the picture quality.) I’d already started taking it apart at that point, so it does look rather untidy. I’ve just rebuilt this machine; and I’m actually writing this article on it.

I stripped it down and started again; therefore I in essence built the machine from scratch. While doing so I took pics of a number of stages and of some of the parts, with a view to blogging the event. This blog has suffered from a lack of posts due to this project and other work, so I  thought it a good idea to use this project as subject matter.

First things first; a motherboard:

I purchased a fairly cheap Gigabyte motherboard for this project: It cost me about £38 at the time. I’d decided to use a socket AM2 AMD Athlon 64 x 2, 2.2GHz processor, as in my other working machine, for this one.

Some people have a low-opinion of AMD chips. Myself, I’ve always found them to be reliable and sturdy. Also they’re cheaper and the motherboards that run them cost less too. Since this was a rebuild that I didn’t want to spend too much on I was quite happy with my choice.

Of course I’d need a CPU cooler too, which consists of a heatsink and fan in order to prevent the processor from overheating. I had this one in stock and was going to use it. However I found that the original cooler was a better one, and surprisingly that it fitted onto a socket AM2 fitting perfectly; therefore having cleaned it up I used it instead.

I also invested in a new hard-drive. I could have used the old one; there was nothing wrong with it. – But I added the old one to my other machine and started this build with a brand new disk.

All-in-all the motherboard, processor, and hard-drive, cost me £108 Inc. VAT at 15%.

So to construction; and the pic on the right shows the case with the new motherboard fitted.

Always remember before starting out; earth thyself: Static electricity builds up in your body and on your clothes, and it kills computer components. personally I always wear an earthed wrist-strap when building computers, just to take any static safely to earth rather than letting it flow through the components I’m using and killing them.

After this point I got a buzz,  and I just ploughed on ahead with construction while not bothering to take any more pics of it.

In short, though, it was just a matter from here of fitting the PSU, connecting the appropriate power leads to the motherboard, inserting the processor into the socket on the motherboard, pulling the little lever while pressing down on it to seal it in the socket, smearing some heat-conducting grease on the top of it, fitting and aligning the cooler, and pulling down the lever on it to tighten it to the surface after clipping the clips onto the processor surround.

Installing the RAM: I inserted 2 x 1GB 667MHz DDR2 sticks into the memory slots and pushed down until they clicked into place.

Following that I connected up the front panel to the appropriate pins. I had problems with the sound jacks on the front as the connections didn’t match with the new motherboard at all. In the end I left the two front sound jacks unconnected, and only connected the 2 front USB ports, the HD activity LED, and the power-indicator LED, to the appropriate pins.

I popped the new HDD into a drive-bay, screwed it in, and connected it up to a SATA power lead from the PSU and to the motherboard’s SATA controller via a SATA connector lead. The same with the DVD-RW drive. (I used the existing DVD-RW as there was no point getting a new one. – Same with the existing floppy-drive.

"Floppy-drive! Why bother with a floppy?" You ask.

I like floppy-drives. I find them useful. I also still like CRT monitors and Outlook Express too. That’s just me: I don’t expect anyone to do similar if they don’t want to.)

So having put the thing together it was time for the initial power-up: Fingers crossed. Bingo: POST. I did take a pic of it, but it was so crappy I deleted it.

After a few minor adjustments to the BIOS, it’s time to install Windows XP:

Pop the XP pro CD into the DVD-RW drive… Let’s get the HDD formatted: NTFS – A decent file-system.

Install Windows…

- Et voila mes amis.

That wasn’t exactly the hardest thing on earth to do; although the construction is the easy, quick, and interesting part for me: It’s the 12 or so hours afterwards installing, optimising, and configuring, all the software that really gets my goat: That’s one reason I don’t do upgrades as a rule for customers: Even after spending 12 hours on it; they still moan about something: That’s why I just build the comp and install and optimise Windows and the motherboard drivers after a new build only, professionally. People can add their own software afterwards and screw up the operating system any way they like once the comp is delivered and paid for.

So that’s the rebuild; and it is a rather excellent job although I do say so myself.